Rotor Bolts
Rotor Bolts
 |
 MAGURA MARTA SL ROTOR - 160MM - NEW - NO RESERVE  US $5.50
|
 Super Light Weight Pro Race Disc Brake Rotor only 79g US $29.99
|
 MAVIC EX721 DISC RIMS,BLUE HOPE PRO 2 EVO DISC HUBS US $511.90
|
 MAVIC XM819 UST DISC RIMS,GOLD,HOPE PRO2 EVO DISC HUBS US $505.58
|
 MAVIC XC717 DISC RIMS,RED HOPE PRO2 EVO DISC HUBS US $496.04
|
 MAVIC XM819 UST DISC RIMS,GUNSMOKE,HOPE PRO2 EVO DISC HUBS US $505.58
|
 MAVIC EX721 DISC RIMS,RED HOPE PRO 2 EVO DISC HUBS US $511.90
|
 MAVIC XM819 UST DISC RIMS,BLUE,HOPE PRO2 EVO DISC HUBS US $505.58
|
 MAVIC EX721 DISC RIMS,GUNSMOKE HOPE PRO 2 EVO DISC HUBS US $511.90
|
 MAVIC XM819 UST DISC RIMS,RED,HOPE PRO2 EVO DISC HUBS US $505.58
|
 MAVIC EN521 DISC RIMS,SILVER HOPE PRO 2 EVO DISC HUBS US $473.98
|
 MAVIC EX721 DISC RIMS,GUNSMOKE HOPE PRO 2 EVO DS HUBS US $492.94
|
 ZTR FLOW DISC RIMS (BLACK),GOLD HOPE PRO2 EVO HUBS F&R US $526.12
|
 MAVIC EN521 DISC RIMS,GOLD HOPE PRO 2 EVO DISC HUBS US $473.98
|
 MAVIC EN521 DISC RIMS,BLUE HOPE PRO 2 EVO DISC HUBS US $473.98
|
 MAVIC EN521 DISC RIMS,RED HOPE PRO 2 EVO DISC HUBS F&R US $473.98
|
 MAVIC EN521 DISC RIMS,GUNSMOKE HOPE PRO 2 EVO DC HUBS US $473.98
|
 MAVIC XC717 DISC RIMS,BLACK HOPE PRO2 EVO DISC HUBS F&R US $496.04
|
 MAVIC EX721 DISC RIMS,BLACK HOPE PRO 2 EVO DISC HUBS US $511.90
|
 MAVIC XM819 UST DISC RIMS,SILVER,HOPE PRO2 EVO DSC HUBS US $505.58
|
 MAVIC XC717 DISC RIMS,GOLD HOPE PRO2 EVO DISC HUBS US $496.04
|
 ZTR FLOW DISC RIMS (BLACK),SILVER HOPE PRO2 EVO HUBS US $526.12
|
 MAVIC EX721 DISC RIMS,SILVER HOPE PRO 2 EVO DISC HUBS US $511.90
|
 ZTR FLOW DISC RIMS (BLACK),GUNSMOKE HOPE PRO2 EVO HUBS US $526.12
|
 MAVIC XC717 DISC RIMS,SILVER HOPE PRO2 EVO DISC HUBS US $496.04
|
 MAVIC EX721 DISC RIMS,GOLD HOPE PRO 2 EVO DISC HUBS US $511.90
|
 ZTR FLOW DISC RIMS (BLACK),BLUE HOPE PRO2 EVO HUBS F&R US $526.12
|
 Hope 2-piece 183mm Rotor US $64.99
|
 Hope 160mm Lightweight Rotor Floating US $60.99
|
 Hope 160mm Floating Rotor Pink w/ Flowers US $55.99
|
 Avid Elixir X.0 Black/Red 160mm HS1 Rear Disc Brake US $230.99
|
 Hayes 8" Rotor V8 w/ Screws US $30.99
|
 Hayes 6" Rotor V6 w/ Screws US $25.99
|
 Avid G3 Clean Sweep Rotor 203mm US $45.99
|
As the mechanical seal positions?
Mechanical seal mechanical seal installation location is a very important task. Positioning of the so-called ring is to determine the axial position of the sleeve. If this is the first time, but also try to install the mechanical seal installation. This mechanical seal, the rotor should be installed to the normal position. Axial be determined axial string can not exceed 0.30mm, the balance in order to determine the location of the axis of the rotor disk, the balance on the plate and disk space pushed the balance (equilibrium contact your face.) As a single rotor, light, pump parts without contact and friction.
Based on this job for mechanical seals. This static pages gland the first installation of the pump rotor shaft after the entry of a trade mark, mark the location of cables on the rear window and measure the thickness of the static part of the gland, Spring center ring of this free from the axis point values for a length of 1 s, obtained in the B-axis, from the point of constant motion, Block B, Sealing mechanical work is complete. S is a fraction of the amount of compression mechanical seals. If the original pump is equipped with a mechanical seal, the installation work of demolition should be prepared before demolition overlooked point mark, while the original seal of the transmission block installation location is correct.
Mechanical seals of the installation steps?
1st Do pre-installation inspection and preparation.
2nd Static ring on the gland assembly.
3rd The ring and transfer the place of assembly.
4th Mechanical seals, and attached to the sleeve on the driver's seat.
5th Installing stationary ring gland. Pressed in a screw cap to protect against the final slope, even the screws. Contact the glands and the end of the sensor gap closed field, the error is not a sub-0.04mm. Check the gland ring and the static clearance points along the shaft around the error is less than 0.10mm.
6th gland controls the ban, the static and the ring shaft (sleeve), whether the car is to feel the friction plate should be uniform, light.
7th Installation additional devices, such as washing and cooling water, coolers, filters and so on.
8th Pump inlet valves open, the introduction of media studies static pressure seal check. If there is no leakage, slow car, check for leaks while excluding closed gas chambers (this is very important), gradually pick up speed of the car on the drive, and then start the pump, no leaks or minor leaks can be started or stopped the pump mode.