Rotor Bolts
Rotor Bolts
 |
 TEKTRO IO Disc Brake Front & Rear 160 Rotor Black C114  US $54.03
|
 TEKTRO Draco Hydraulic F&R Brake 160 Rotor White C116 US $129.69
|
 TEKTRO Auriga Hydraulic Disc F&R Brake 160mm Rotor C115 US $125.36
|
 16 Disc Brake Caliper Alignment Shims 0.3mm 0.5mm 1mm US $3.99
|
 Hope Mono Mini Rotor 160 MM - Gold (One Rotor) US $64.99
|
 Hope Moto M6 Rotor 203 MM - Red (One Rotor) US $64.99
|
 V2 Moto Floating Rotor 203 MM - Black (One Rotor) US $64.99
|
 Hope Mono M4 Rotor 203 MM - Gun Smoke (One Rotor) US $64.99
|
 sram avid xx Front 160 hydraulic disc brake set new with mmx disc US $249.98
|
 Avid BB7 Road Disc Brake Caliper & 140mm G2 Rotor Platinum Rear US $70.99
|
 MOWA DISK ROTOR BOLTS/SCREWS /12 PCS / RED US $14.99
|
 2012 Avid Elixir X.0 Black/Black 180mm HS1 Front US $230.99
|
 ALLIGATOR CENTER LOCK ROTOR DISC ADAPTER BLACK c US $19.99
|
 Bike Alligator Disc Rotor WIND CUTTER 180 mm MTB ROAD US $24.95
|
 Gatorbrake ALLIGATOR WIND TI Disc Brake Rotor 140MM US $27.95
|
 Gatorbrake Stainless Steel Disc Brake Rotor 180mm 113g US $25.95
|
 Gatorbrake BIKE Steel Disc Brake Rotor 160mm 76g US $24.95
|
 Gatorbrake Stainless Steel Disc Brake Rotor 160mm 88g US $12.85
|
 Hope Tech X2 EVO Brakes 160/140steelRotors - 6 Bolt/postMt US $439.99
|
 Ashima Airotor Disc Brake Rotor 180 mm MTB 112g Black US $31.00
|
 KCNC Razor Stainless Disc Brake Rotor MTB 180 94g 2pc US $73.00
|
 Mavic XC 717 Disc Coda Expert Sun DS1 Bike Disc Wheels US $64.99
|
As the mechanical seal positions?
Mechanical seal mechanical seal installation location is a very important task. Positioning of the so-called ring is to determine the axial position of the sleeve. If this is the first time, but also try to install the mechanical seal installation. This mechanical seal, the rotor should be installed to the normal position. Axial be determined axial string can not exceed 0.30mm, the balance in order to determine the location of the axis of the rotor disk, the balance on the plate and disk space pushed the balance (equilibrium contact your face.) As a single rotor, light, pump parts without contact and friction.
Based on this job for mechanical seals. This static pages gland the first installation of the pump rotor shaft after the entry of a trade mark, mark the location of cables on the rear window and measure the thickness of the static part of the gland, Spring center ring of this free from the axis point values for a length of 1 s, obtained in the B-axis, from the point of constant motion, Block B, Sealing mechanical work is complete. S is a fraction of the amount of compression mechanical seals. If the original pump is equipped with a mechanical seal, the installation work of demolition should be prepared before demolition overlooked point mark, while the original seal of the transmission block installation location is correct.
Mechanical seals of the installation steps?
1st Do pre-installation inspection and preparation.
2nd Static ring on the gland assembly.
3rd The ring and transfer the place of assembly.
4th Mechanical seals, and attached to the sleeve on the driver's seat.
5th Installing stationary ring gland. Pressed in a screw cap to protect against the final slope, even the screws. Contact the glands and the end of the sensor gap closed field, the error is not a sub-0.04mm. Check the gland ring and the static clearance points along the shaft around the error is less than 0.10mm.
6th gland controls the ban, the static and the ring shaft (sleeve), whether the car is to feel the friction plate should be uniform, light.
7th Installation additional devices, such as washing and cooling water, coolers, filters and so on.
8th Pump inlet valves open, the introduction of media studies static pressure seal check. If there is no leakage, slow car, check for leaks while excluding closed gas chambers (this is very important), gradually pick up speed of the car on the drive, and then start the pump, no leaks or minor leaks can be started or stopped the pump mode.