Rotor Bolts
Rotor Bolts
 |
 Hayes V7 Disc Brake Rotors * 7"/178MM * Set of 3 * With Bolts, Shims  US $59.99
|
 ALLIGATOR CENTER LOCK ROTOR DISC ADAPTER GOLD US $19.99
|
 Bike/Bicycle/MTB Disc Brake Rotor 160mm 6" for Shimano US $26.09
|
 2 x M6 15mm Titanium Bolts Rotor Screws Disc Brake NEW US $5.39
|
 Rotor S3X Stem 120mm Red US $174.00
|
 2011 Magura Marta Black Disc Brakes & STORM SL Rotors US $374.95
|
 Mavic Centre-Lock to 6 Bolt Disc Rotor Adaptor US $18.00
|
 FORMULA ORO K24 Hydraulic Disc Brake Front 800mm NEW US $89.97
|
 FORMULA ORO K18 Hydraulic Disc Brake Front 950mm NEW US $59.97
|
 Crank Brothers Front 16 Hole Hub US $100.00
|
 NEW FRONT & REAR DISC BRAKE SET 160MM ROTORS, BIKE BICYCLE, 4 SETS AVID BB5 PADS US $53.36
|
 AVID 2011 CODE REAR MTB HYDRAULIC DISC BRAKE - 203mm US $255.95
|
 Gatorbrake STARLITE Ti Titanium Disc Rotor 180 MTB Bike US $32.50
|
 New MOWA Disc Rotor Bolts, M5x10mm, Blue US $15.95
|
 2011 Avid SRAM XX WC Disc Brake 140mm Rear w/ RH Lever US $309.95
|
 2PCS Gatorbrake ALLIGATOR WIND Disc Brake Rotor 140MM US $39.95
|
 2011 Avid SRAM XX WC Disc Brake 185mm Front w/ LH Lever US $309.95
|
 New SRAM XX Disc MTB Brake 140mm Rear with RH Lever US $384.98
|
 New SRAM XX Disc MTB Brake 185mm Front with RH Lever US $384.00
|
 Avid 2012 Code R 180mm HS1 Front Graphite Gray US $162.99
|
 Avid 2012 Code R 180mm HS1 Rear Graphite Gray US $162.99
|
 Avid MTB BB7 BB5 DISC BRAKE ROTOR 160 mm 6bolt Pair New US $18.99
|
As the mechanical seal positions?
Mechanical seal mechanical seal installation location is a very important task. Positioning of the so-called ring is to determine the axial position of the sleeve. If this is the first time, but also try to install the mechanical seal installation. This mechanical seal, the rotor should be installed to the normal position. Axial be determined axial string can not exceed 0.30mm, the balance in order to determine the location of the axis of the rotor disk, the balance on the plate and disk space pushed the balance (equilibrium contact your face.) As a single rotor, light, pump parts without contact and friction.
Based on this job for mechanical seals. This static pages gland the first installation of the pump rotor shaft after the entry of a trade mark, mark the location of cables on the rear window and measure the thickness of the static part of the gland, Spring center ring of this free from the axis point values for a length of 1 s, obtained in the B-axis, from the point of constant motion, Block B, Sealing mechanical work is complete. S is a fraction of the amount of compression mechanical seals. If the original pump is equipped with a mechanical seal, the installation work of demolition should be prepared before demolition overlooked point mark, while the original seal of the transmission block installation location is correct.
Mechanical seals of the installation steps?
1st Do pre-installation inspection and preparation.
2nd Static ring on the gland assembly.
3rd The ring and transfer the place of assembly.
4th Mechanical seals, and attached to the sleeve on the driver's seat.
5th Installing stationary ring gland. Pressed in a screw cap to protect against the final slope, even the screws. Contact the glands and the end of the sensor gap closed field, the error is not a sub-0.04mm. Check the gland ring and the static clearance points along the shaft around the error is less than 0.10mm.
6th gland controls the ban, the static and the ring shaft (sleeve), whether the car is to feel the friction plate should be uniform, light.
7th Installation additional devices, such as washing and cooling water, coolers, filters and so on.
8th Pump inlet valves open, the introduction of media studies static pressure seal check. If there is no leakage, slow car, check for leaks while excluding closed gas chambers (this is very important), gradually pick up speed of the car on the drive, and then start the pump, no leaks or minor leaks can be started or stopped the pump mode.